worf a écrit :Salut titix,
Et merci pour l'info, restera plus qu'à mettre la traduction en ligne de la manip lorsqu'elle sera disponible.

Si tu veux je m'y colle.
worf

au secours
I took delivery of a PLV-Z1 last week but I've been having the fan spin up problem - about every 20-25 mins it spools up for about 1 minute. Following the hints on using the Service menus elsewhere in this forum, I've been investigating what the fan settings do. I haven't actually figured it all out but I've made some progress and hope this will get the ball rolling on solving this.
Firstly, get into the 'Service menu' by pressing 'Menu" and "Input" for 5 seconds (don't confuse yourself the way I did by getting into the 'Factory Menu' via 5 secs on the "Select" and "Input" buttons...). You get out of the menu by pressing the power button on the remote.
The relevant entries are numbers 51-75, when these are selected it also displays the 4 fan speeds and three temperature sensor readings.
My temperatures (these look about right to be degrees C, although I suppose they could just be any old numbers) are roughly:
Temp A 34-35
Temp B 70-75
Temp C 46-48
My values (as set by Sanyo) and what I think they do are as follows.
Where I use a number in [] in the description I am referring to another menu entry number.
Note that for the fan speeds, lower numbers correspond to higher speeds.
-----------------------------------------------------
No. - default - Description
-----------------------------------------------------
51 - 0 - if =0, use variable speed fan
if =1 use fan settings in [72-75]
52 - 172 - These four positions are the
53 - 197 - fan speeds when in 'normal' bulb
54 - 172 - mode speed
55 - 156 - settings
56 - 79 - Fan speeds
57 - 79 - for high
58 - 79 - speed
59 - 79 - fan mode
60 - 36 - 'Soft' Temp A limit, above this temp the fan
speeds gradually increase if [51] set =0
The higher the difference between Temp A
and this number, the faster the fans turn
61 - 45 - 'Hard' Temp A limit - fans go to high speed
mode (ie [56]-[59]) above this temp.
62 - 47 - Temp A - protection cut out (?) This is a
guess, I didn't test it.
63 - 75 - Temp B limit - fans go to high speed above
this number and stay there until Temp B has
dropped back below [66]
66 - 63 - Temp B, high speed fan stops once the
temp gets back below this number
67 - 76 - Temp B - high temperature protection cut out
(unlike [62] I did test this one - you have to
be quick to turn it back up when you turn
the projector back on, otherwise it turns
itself off again - careful!!!).
68 - 16 - ?
69 - 3 - ?
70 - 3 - ?
71 - 0 - When set >0 the fans adopt faster speeds
when Temp A is <[60]
(This is backwards - it makes no sense...I
would expect it to kick in when >[60])
72 - 79 - Fan speed settings for
73 - 79 - when [51] set =1
74 - 79 -
75 - 79 -
-----------------------------------------------------
So what is causing the fan spool up?
Watching the temperatures for a while it soon becomes clear. The default fan settings aren't holding the Temp B value down and it gradually creeps upwards. Eventually it hits the value set in [63] - ie 75C (I assume this is the bulb holder compartment temperature sensor). The fans then kick to high speed until they've cooled it back down to [66]=63C. Things then go quite again for 30 mins or so until it gets back up to 75C.
Obviously this is going to be affected by the outside air temperature. I note that not many people on the forum have complained about this but I wonder whether this is becuase it is winter in North America and Europe at the moment (I assume where most of the forum members are). I'm in Hawaii so have possibly have a warmer room than most of you? Are we going to see lots more complaints along these lines where summer arrives - the projector isn't old enough to have had a summer in peoples homes yet.
One other relevant bit of information is that Fan 3 (the main exhaust fan) is by far the noisiest. So it seems to me that the strategy should be to try and keep that one as slow as possible.
So there are two possible solutions that I can see:
1) Decrease [60]. This will cause all the fans to spin up gradually a little earlier than previously, hopefully this will keep Temp B from hitting it's limit.
2) Set [51] =1 and then adopt some other values for [72]-[75]
I originally choose the latter option and set them as follows:
[72]=193
[73]=205
[74]=197
[75]=189
This seemed to stop the fan spooling for me.
However, this seems to completely disable the vaiable fan speeds - it uses these numbers irrespective of the bulb setting and it also disables the high speed fan when it goes above 75C - I assume the overheat protection still applies (although I didn't test this).
So now I'm experimenting with changing [60] to 33C, which also seems to work so far.
Outstanding items are:
1) Is it possible to combine the new fan speeds with the mode where they speed up more if Temp A exceeds it's 'soft' limit - if there is I can't figure out how...
2) What do positions [68]-[70] do.
3) What other stuff have I missed??
It would be great if a couple of you who don't have the fan spool up problem could confirm what default settings you have.
Also what temperatures are other people seeing - I assume running at close to the 75C mark is what Sanyo want you to do in order to get an OK bulb life time - hotter=shorter life, cooler=longer life (I think).
source:
http://www.avsforum.com/avs-vb/showthre ... did=218832